Scrape, blot or vacuum excess material.  Saturate spot with DETERGENT (Sure-Pass), allow to set 1 minute, tamp vigorously with brush, flush with water, extract or blot dry.  Repeat if necessary.

Moisten spot with NON-VOLATILE SOLVENT (Invade), allow to set 5 minutes, tamp occasionally with tamping brush.  Apply DETERGENT (Sure-Pass), tamp, flush out with water, extract or blot dry.  Repeat if necessary.

Moisten spot with VOLATILE DRY SOLVENT (Trounce) and blot with cloth removing as much as possible.  Moisten spot with NON-VOLATILE SOLVENT (Invade), allow 5 minutes with occasional agitation using tamping brush.  Flush with DETERGENT (Sure-Pass), agitate, extract or blot dry. 

Saturate spot with DETERGENT (Sure-Pass), allow to set 2 minutes, agitate with tamping brush, flush with water, extract or blot dry.  Apply ACID SPOTTER (Surely or Restore) and allow to set 2 minutes, extract or blot dry.

Saturate spot with RUST REMOVER (Rustle, Rust-Off, Novel), watch the color disappear, flush with water, extract or blot dry.  Repeat if necessary.

Steam the spot by covering with white towel and applying a steam iron to the spot.  The wax will melt and transfer to the towel.  Moisten the spot with VOLATILE DRY SOLVENT (Trounce), blot dry, then saturate the spot with DETERGENT (Sure-Pass), allow to set 1 minute, agitate with tamping brush, flush out with water, extract or blot dry.

Mix 1 ounce (5 capfuls) of ENZYME CLEANER (Relief) in a quart of hot (120-140°F) water, apply this solution to the spot and cover with a warm, damp, white towel.  Allow to set for 30 minutes, flush out with water, extract or blot dry.  Repeat if necessary.

Use CAUTION, test for loss of color in an inconspicuous place.  Mix one cap of REDUCING AGENT (Apart) into one cup of warm water.  Apply liberally to the spot and cover with cloth for 10 minutes,  Repeat if necessary.  Flush out with water, extract or blot dry.

Moisten spot with NON-VOLATILE SOLVENT (Laser).  Apply DETERGENT (Sure-Pass) immediately after to prevent bleeding, flush out with water, extract or blot dry.  Repeat if necessary.

Saturate the area with DETERGENT (Sure-Pass), working in with tamping brush, flush with water and extract or blot dry.  Saturate area with DEODORANT (Attest, Cycle, Krisp), extract or blot dry. 

Saturate the spot with DETERGENT (Sure-Pass), allow to set 2 minutes, agitate with tamping brush, flush with water, extract or blot dry.  Apply ACID SPOTTER (Surely or Restore) to the spot and allow to set 2 minutes, extract or blot dry.  If the spot is not out, it may be a DYE, so, proceed as follow:

Test carpet in an inconspicuous place for possible loss of color or pattern by saturating a test spot with DYE REMOVER (Press-It), covering with a white cotton or paper towel and apply steam from a steam iron for 30 seconds.  If no color shows on the towel, repeat the same procedure for 15-20 seconds on the spot.  Keep towel and spot wet with DYE REMOVER (Press-It) and move towel on each press.  When spot is removed flush out with water, extract or blot dry.

Remove excess gum with scraper, punch holes in remaining gum, apply GUM REMOVER (Exclude, Krush-Solv, Krush-Gel) and allow 2 minutes.  Extract with hot water r remove with damp cloth.  When you can no longer see any material, saturate area with DETERGENT (Sure-Pass), agitate with bone scraper, flush with eater, extract or blot dry. 

Moisten cloth with GUM REMOVER (Exclude, Krush-Solv, Krush-Gel) and blot lightly, keeping the adhesive or varnish wet so that it will slowly absorb onto the cloth.  When you can no longer see any material, saturate area with DETERGENT (Sure-Pass), agitate with bone scraper, flush with water, extract or blot dry.

On reoccurring spots simply reclean with appropriate procedure.  Cover the spot with a clean towel, and weight it down until dry.  The spot that comes back simply absorbs into the towel and leaves the carpet clean.

Saturate the spot with DETERGENT (Desolv), allow to set 2 minutes, agitate with tamping brush, flush with water, extract or blot dry.  Apply ACID SPOTTER (Surely or Restore) to the spot and allow to set 2 minutes, extract or blot dry.  If the spot is not out, it may be a DYE, So proceed as follows:

Test carpet in an inconspicuous place for possible loss of color or pattern by saturating a test spot with DYE REMOVER (Press-It), covering with a white cotton or paper towel and apply steam from a steam iron for 30 seconds.  If no color shows on the towel, repeat the same procedure for 15-20 seconds on the spot.  Keep towel and spot wet with DYE REMOVER (Press-It) and move towel on each press.  When spot is removed flush out with water, extract or blot dry.